Whole-Home Repiping in McKinney, TX
When an under-slab line has leaked more than once, or the detection report shows it is failing along its length, the repair that lasts is not another spot fix — it is a repipe: new lines through the walls and attic, and no more pipe in the soil.
Need help with a slab leak?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
What this service does
Repiping is the answer to a different question from spot repair. A spot repair asks: where is this leak, and how do we fix it? Repiping asks: is this line going to leak again? In McKinney, that question comes up often, because the soil under the city never stops moving. Houston Black clay swells when wet and shrinks when dry, and every cycle flexes the pipes buried in it. A copper line that has been flexed for twenty years can fail at one joint this year and another joint the next — and each failure means another opening in the floor.
A repipe removes the line from the soil altogether. The failing under-slab lines are abandoned in place, and new lines are run through the walls and the attic, from the water heater and the main supply to every fixture in the house. Nothing new goes under the slab. The soil can move as it likes; there is no pipe in it to stress. That is the whole idea, and it is why repiping is the usual recommendation when a line has leaked twice, or when the detection report shows the line is in poor condition along its length.
The work is larger than a spot repair, and it is honest to say so. A repipe touches more of the house — walls are opened at fixture points, lines are run through the attic, and the water is off while the changeover happens. But it is one job instead of several, and it ends the cycle of leak, repair, leak again. For a homeowner who has already paid for two spot repairs on the same line, the arithmetic is plain: the third leak costs more than the repipe would have.
The pipe material matters, and it is worth understanding. Older McKinney homes often have copper under the slab — durable, but rigid, and rigid pipe is what soil movement punishes. Newer repipes usually use PEX, a flexible plastic pipe that bends with movement instead of resisting it, or CPVC. The choice follows the house, the water, and the layout. What does not change is the route: through the walls and attic, never under the slab again.
One thing people get wrong about repiping is the timing. Many homeowners wait for the second or third leak before considering it, and each leak in between washes out more soil and soaks more flooring. The detection report is the moment to decide: if it shows one leak in a sound line, spot repair is right. If it shows a line that is failing along its length, repiping is the repair that lasts — and deciding it at the first leak, rather than the third, saves the floor from being opened twice.
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.
How whole-home repiping works in a McKinney home
The job starts with the detection report and a map of the house: which lines run under the slab, which fixtures they feed, and which of them have failed or are failing. The new route is planned from that map — through the walls and attic, from the main supply and the water heater to each fixture. The plan is drawn before any wall is opened, because the route decides how much of the house the work touches.
The new lines are run first, while the old lines are still in place and the water is still on. Walls are opened at fixture points — behind sinks, showers, toilets and the washing machine — and the new pipe is run through the attic and down the walls. The openings are small and local, at the points where the pipe has to reach a fixture. When the new lines are in place, the water is switched over: the old under-slab lines are capped and abandoned in place, and the new lines take over.
Then the testing starts. Every new line is pressure-tested, every fixture is run, and the meter is checked with every tap off. The old lines stay in the ground, capped and empty — digging them out would mean opening the slab for no reason, so they are left where they are. The wall openings are patched, the fixtures are put back, and the water is on again through lines that no longer run through moving clay.
What the service includes
Line mapping and repipe plan
The under-slab lines are mapped, the new route through walls and attic is planned, and the fixtures are listed before any wall is opened.
New supply lines
New hot and cold lines run through the walls and attic to every fixture, replacing the failing under-slab lines.
Abandoning old lines
The old under-slab lines are capped and left in place — digging them out would mean opening the slab for no reason.
Fixture reconnection
Every sink, shower, toilet, washing machine and water heater is reconnected to the new lines.
Pressure testing
Every new line is pressure-tested, every fixture is run, and the meter is checked with every tap off.
Wall patching
The small openings at fixture points are patched, and the fixtures are put back.
How the work runs
Detection report and map
Which lines run under the slab, which have failed, and what the rest of the line looks like.
Plan the new route
Through the walls and attic, from the main supply and water heater to every fixture.
Run the new lines
Walls are opened at fixture points and the new pipe is run through the attic and down the walls.
Switch the water over
The old under-slab lines are capped and abandoned, and the new lines take over.
Test everything
Every line is pressure-tested, every fixture is run, and the meter is checked with every tap off.
Patch and finish
Wall openings are patched, fixtures are put back, and the water is on again through the new lines.
Tools and methods used
PEX piping and fittings
Flexible pipe that bends with movement instead of resisting it, run through walls and attic.
Pipe locator and detection report
The map of the old under-slab lines, which the new route is planned from.
Pressure test gauge
Verifies every new line holds pressure before the water is switched over.
Drywall patching tools
Close the small openings at fixture points after the new lines are in place.
Repipe vs spot repair: how to decide
The decision is made from the detection report, not from a preference. One leak in a sound line, with the rest of the line testing well, is a spot repair — a smaller job, a smaller opening, and the right repair for a line that is otherwise healthy. Two leaks on the same line, or a line that loses pressure along its length, is a repipe — the line itself is the problem, and fixing one spot on it leaves the next failure in place.
Age matters too. A line that is twenty years old in Houston Black clay has been flexed by two decades of wet and dry seasons. A line that is five years old has not. The report records the age, the material, and the test results, and the recommendation follows from those three things. A homeowner who has already had two spot repairs on the same line has already made the decision in practice — the repipe is the job that ends the cycle.
What repiping does not do
Repiping replaces the water lines. It does not fix the foundation, and it does not dry a floor that is already wet — those are separate jobs, done after the pipe work. It also does not replace the drain and sewer lines, which run under the slab too and are a different system with their own detection and repair. A repipe covers the supply lines: hot and cold water to every fixture.
Repiping also does not change the water. If the home has hard water, the new lines face the same water the old ones did — and the water heater, the fixtures, and the new lines all live with it. What changes is the route: the lines are no longer buried in soil that moves, and that is the change that matters.
Failing lines buried in moving clay soil
A leak under the slab keeps running — washing out soil, lifting flooring, and stressing the foundation.
New lines through the walls and attic
The leak is located with listening and electronic equipment before any concrete is opened.
Problems whole-home repiping solves
- A line that has leaked more than once
- A line failing along its length, not at one spot
- Repeated spot repairs on the same line
- Old copper lines flexed by twenty years of clay soil movement
- A home where every new leak means another opening in the floor
- A detection report that shows the line itself is the problem
Signs you need whole-home repiping
- Two or more leaks on the same under-slab line
- A line that loses pressure along its length
- A detection report showing poor line condition
- Repeated damp patches in different rooms
- A water bill that jumps again after a previous repair
- Discoloured water from ageing lines
- Low pressure that returns after a spot repair
- A home with original lines in Houston Black clay, twenty years on
Related problems
High water bill · Low water pressure · Warm spot on the floor
Industries that use this service
Rental Properties · Apartments & Condos · Commercial Offices · All industries →
Frequently asked questions
Questions people ask about whole-home repiping, answered plainly.
When the line has leaked more than once, or when the detection report shows it is failing along its length. One leak in a sound line is a spot repair. Two leaks on the same line, or a line that loses pressure along its length, means the line itself is the problem — and repiping is the repair that lasts.
Longer than a spot repair — the new lines have to be run through the whole house, and every fixture has to be reconnected and tested. The schedule depends on the size of the home and the number of fixtures, and it is known before the work starts, from the repipe plan.
The water is off while the changeover happens — when the old lines are capped and the new lines take over. The new lines are run first, while the old lines are still in place and the water is still on, so the outage is kept to the changeover itself.
They are capped and left in place. Digging them out would mean opening the slab for no reason, so they stay where they are, empty and sealed. Nothing new goes under the slab.
Usually PEX, a flexible pipe that bends with movement instead of resisting it, or CPVC. The choice follows the house, the water, and the layout. Older homes often have copper under the slab — durable, but rigid, and rigid pipe is what soil movement punishes.
No. Repiping replaces the water lines. If the slab has moved or the foundation needs attention, that is a separate question, answered after the pipe work — not before. The repipe stops the leaks that wash out soil; it does not undo movement that has already happened.
No. A repipe covers the supply lines — hot and cold water to every fixture. Drain and sewer lines run under the slab too, and they are a different system with their own detection and repair.
Walls are opened at fixture points — behind sinks, showers, toilets and the washing machine — where the new pipe has to reach a fixture. The openings are small and local, and they are patched when the work is done.
Slab leak in your McKinney home?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Call now for slab leak help
Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.