McKinney & the DFW metro · Slab leak helpMon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Water line leak detection McKinney, TX hero
Home › Services › Water Line Leak Detection

Water Line Leak Detection in McKinney, TX

The supply lines that feed a home run from the meter to every tap — under the slab, through the walls, and into the attic. A leak anywhere on that route shows up as a bill, a sound, or a damp patch. Detection finds which line, and where.

Call Now

McKinney & the DFW metroDetection, location & repairPinpoint location before any digging

Need help with a slab leak?

Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.

Call Now

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

1
Shut the water off firstThe main supply stops the leak at its source — if you can reach it safely.
2
Pinpoint the leakListening equipment and electronic location find the leak before any concrete is opened.
3
Repair under the slabSpot repair, tunnelling, or repiping — the method follows the leak, not the other way round.
4
Document everythingPhotos, meter readings and notes help when you talk to your insurer.
Water Line Leak Detection

What this service does

A home has two kinds of water lines, and they fail differently. The supply lines carry water under pressure from the meter to every fixture — the kitchen, the bathrooms, the washing machine, the water heater. The drain lines carry water away, downhill, without pressure. A supply leak runs all the time, because the line is always pressurised; a drain leak runs only when water goes down the drain. That difference is the first thing detection uses to tell them apart.

Supply line leaks are the ones that cost water. A small leak under the slab can run for weeks before anyone notices, because the water goes into the soil, not onto the floor. The first sign is usually the bill: a jump with no change in use. The second is the sound: running water when every tap is off. The third is the floor: a damp patch, a warm spot on a hot line, or flooring that lifts. Any one of them is a reason to check the meter with every tap off.

The supply route in a McKinney home is worth picturing. The main line comes in from the meter, usually near the street, and runs to the house — often under the slab, sometimes through the wall. Inside, it splits: cold lines to every fixture, and a line to the water heater, which feeds the hot lines back through the house. A leak can sit on any part of that route, and the detection work is a process of narrowing it down: meter, pressure test, listening, location.

Hot and cold lines are tested separately, because they fail differently and the signs point to one or the other. A warm floor points to the hot line. A bill that jumped with no warm floor points to the cold line. A pressure drop on one line and not the other confirms it. The separation matters, because the repair for a hot line leak and a cold line leak can be different — and because the water heater is on the hot side, and a hot line leak can look like a water heater problem.

One thing people get wrong about supply leaks is assuming the leak is under the slab. It often is, in McKinney, because so much of the supply route runs under the slab. But a supply leak can also sit in a wall, in the attic, or at a fitting behind a fixture — and each of those is found differently. Detection follows the line, not the assumption, and the location is confirmed before any work is planned.

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the damp floor, the water meter, and the rooms affected.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the signs started, and whether the water meter moves when every tap is off.

Call Now

Understanding

How water line leak detection works in a McKinney home

The visit starts at the meter. Every tap, toilet, washing machine and ice maker is turned off, and the meter is watched. A meter that moves with everything off means a leak on the house side of the meter. A meter that holds still means the leak is not on the supply side — a running toilet, a dripping tap, or a drain line. That first test takes a few minutes and it decides everything that follows.

Then the lines are tested separately. The hot and cold supply lines are isolated and pressure-tested one at a time. A line that holds pressure is sound; a line that loses pressure is leaking, and the size of the drop gives a sense of how large the leak is. The water heater is checked too, because a hot line leak can look like a water heater problem, and the two have to be separated before any work is planned.

Then the listening starts. The operator works across the floor and along the walls with an acoustic sensor, following the sound of escaping water to its loudest point. Electronic line location traces the pipe, so the crew knows which line is leaking and which direction it runs. When the methods agree, the leak is marked — on the floor, on the wall, or in the attic — and the report records the line, the location, and what the rest of the line looks like.

Water line leak detection McKinney, TX 1
Water line leak detection McKinney, TX 2
Water line leak detection McKinney, TX 3
Included

What the service includes

Meter test

The water meter is checked with every tap off, to confirm a leak on the house side of the meter.

Hot and cold line pressure tests

The supply lines are isolated and tested separately, so the leaking line is identified.

Acoustic listening

A sensitive microphone follows the sound of escaping water to its loudest point.

Electronic line location

The pipe is traced so the crew knows which line is leaking and which direction it runs.

Water heater check

The water heater is checked, because a hot line leak can look like a water heater problem.

Leak marking and report

The leak is marked and the report records the line, the location, and the condition of the rest of the line.

Process

How the work runs

1

Call and describe the signs

A bill that jumped, running water with every tap off, a warm or damp floor — and where they show up.

2

Meter test

Every tap off, the meter watched — a moving meter means a leak on the house side.

3

Pressure tests

Hot and cold lines tested separately to identify the leaking line.

4

Listening and location

Acoustic listening follows the sound; electronic location traces the pipe.

5

Mark the leak

The location is marked and the report is written, with the line and its condition.

6

Repair decision

Spot repair, tunnelling, or repiping — the method follows the leak and the line.

Water line leak detection McKinney, TX process 1
Water line leak detection McKinney, TX process 2
Water line leak detection McKinney, TX process 3
Water line leak detection McKinney, TX process 4
Tools & methods

Tools and methods used

Acoustic ground microphone

Hears the sound of escaping water through concrete, flooring and walls.

Electronic pipe locator

Traces buried and in-wall water lines so the leaking line is identified.

Pressure test gauge

Tests the hot and cold lines separately, and verifies the repair afterwards.

Thermal imaging camera

Reads floor temperatures to find the warm area above a hot water line leak.

Water line leak detection McKinney, TX equipment
Water Line Leak Detection

Supply leaks vs drain leaks

A supply leak runs all the time, because the line is always under pressure. A drain leak runs only when water goes down the drain — a shower, a flush, a washing machine cycle. That difference is the first test: if the meter moves with every tap off, the leak is on the supply side. If the meter holds still but the floor is damp after a shower, the leak is on the drain side.

The signs differ too. A supply leak shows up as a bill that jumped, a sound of running water, or a warm floor on a hot line. A drain leak shows up as a damp patch that appears after use, a smell near a drain, or slow drains. The detection methods differ as well: supply lines are pressure-tested and listened to; drain lines are checked with a camera or a smoke test. The two systems share the house, but they are investigated differently.

Water Line Leak Detection

Where supply leaks happen in McKinney homes

Under the slab is the most common place, because that is where much of the supply route runs — and because the Houston Black clay under the slab moves with every wet and dry season, stressing the pipes buried in it. Joints and fittings are the usual failure points: a copper joint flexed by soil movement for twenty years, a fitting that was stressed during construction.

The other places are the walls and the attic. A line in a wall can fail at a fitting behind a fixture, and the water soaks the drywall before it shows on the floor. A line in the attic can fail at a joint and drip onto the ceiling below. The detection work follows the line wherever it runs, and the location is confirmed before any work is planned.

Problem

A supply line leaking somewhere on its route

A leak under the slab keeps running — washing out soil, lifting flooring, and stressing the foundation.

Solution

The leaking line identified and located

The leak is located with listening and electronic equipment before any concrete is opened.

Problems solved

Problems water line leak detection solves

  • A bill that jumped with no change in use
  • The sound of running water when every tap is off
  • A warm floor on a hot supply line
  • Low water pressure across the house
  • Not knowing whether the leak is supply or drain
  • A hot line leak that looks like a water heater problem

Call Now

Signs

Signs you need water line leak detection

  • A water bill that rises without explanation
  • The sound of running water with every tap off
  • A water meter that moves when everything is off
  • A warm patch on the floor
  • Damp flooring or carpet that returns after mopping
  • Low water pressure in more than one room
  • Discoloured water from a tap
  • A damp wall at floor level with no visible source
Questions

Frequently asked questions

Questions people ask about water line leak detection, answered plainly.

The meter test is the check. Turn off every tap and appliance, then watch the water meter — if it keeps moving, water is going somewhere it should not, and the leak is on the supply side. If the meter holds still, the leak is more likely on the drain side, or a running toilet or dripping tap.

A warm floor points to the hot line; a bill that jumped with no warm floor points to the cold line. The lines are pressure-tested separately to confirm which one is leaking, because the repair for each can be different — and because a hot line leak can look like a water heater problem.

A home can have two leaks — a supply leak under the slab and another in a wall, or a supply leak and a drain leak. That is why the meter is checked again after every repair: a meter that still moves means there is more to find.

Because the water goes into the soil under the slab, not onto the floor. A small supply leak can run for weeks before the floor shows anything — and the bill is the first sign. The meter test with every tap off is the check that confirms it.

No. Low pressure can come from a municipal issue, a closed valve, or a clogged line. If neighbours have normal pressure and yours has dropped, and the meter moves with every tap off, a leak is a likely cause — and the pressure test confirms it.

Under the slab is the most common place, because much of the supply route runs there and the Houston Black clay moves with every wet and dry season. Joints and fittings are the usual failure points. Leaks also happen in walls and attics, at fittings behind fixtures.

Yes. A hot line leak can look like a water heater problem, and the two have to be separated before any work is planned. The water heater is checked as part of the hot line test.

Then it is not a house leak. A meter that holds still with everything off, or a leak visible between the street and the meter, points to the city side — and the water provider is the call to make. The meter test is what separates the two.

Slab leak in your McKinney home?

Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.

Call Now

Contact

Call now for slab leak help

Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

Call Now

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the damp floor, the water meter, and the rooms affected.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the signs started, and whether the water meter moves when every tap is off.
McKinney Slab Leak Pros — helper
☎ Call Now