McKinney & the DFW metro · Slab leak helpMon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Problem high water bill McKinney, TX hero
Home › Problems › Unexplained High Water Bill

Unexplained High Water Bill in McKinney

A water bill that jumps with no change in use is one of the strongest slab leak signs there is. The water is going somewhere it should not — and the meter test finds out where.

Call Now

McKinney & the DFW metroWhat to do firstHow the cleanup works

Need help with a slab leak?

Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.

Call Now

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

1
Shut the water off firstThe main supply stops the leak at its source — if you can reach it safely.
2
Pinpoint the leakListening equipment and electronic location find the leak before any concrete is opened.
3
Repair under the slabSpot repair, tunnelling, or repiping — the method follows the leak, not the other way round.
4
Document everythingPhotos, meter readings and notes help when you talk to your insurer.
Problem
Problem high water bill McKinney, TX

Why the bill is the first sign

A slab leak under the concrete is hidden by the floor, so the bill is often the first sign of it. The water goes into the soil under the slab, not onto the floor, and a small leak can run for weeks before the floor shows anything. The bill, though, shows it immediately: water that leaks away is water that is metered, and the meter does not care whether the water reached a tap or the soil.

The jump is usually clear. A bill that rises a little, month after month, can be a change in use — a new washing machine, a garden, a houseguest. A bill that jumps in one month, with no change in use, is a leak until proven otherwise. The size of the jump gives a sense of the size of the leak: a small jump is a small leak, a large jump is a large one, and a meter that spins fast with every tap off is a leak running now.

How to check the meter

The meter test takes a few minutes and it is the most useful test a homeowner can do. Turn off every tap, toilet, washing machine, ice maker and irrigation system in the house, then watch the water meter — usually in a box near the street or on the side of the house. If the dial keeps moving, water is going somewhere it should not, and the leak is on your side of the meter. If the meter holds still, the leak is not on the supply side.

The test has to be done with everything off, and that includes the things people forget: the ice maker, the irrigation system, a dripping tap, a running toilet. Any one of them can move the meter and look like a leak. Turn them all off, wait, and watch. A meter that moves slowly is a small leak; a meter that spins fast is a large one. Either way, the next step is detection.

What happens after the meter test

If the meter moves, the leak is confirmed and the detection work starts: the hot and cold lines are pressure-tested separately, acoustic listening finds the leak through the floor, and electronic line location traces the pipe. The leak is marked on the floor and the repair plan is made from that location. If the meter holds still, the investigation turns to the drain side — a camera in the drain line, or a smoke test — because a drain leak does not move the meter.

The bill itself is worth keeping. The insurer asks for the record — the bills that show the jump, the date it started, and the meter readings from the detection visit. The bill is the evidence that the leak started on a date, and that it was found by testing, not by guessing.

What to do now

  • Turn off every tap, toilet, appliance and irrigation system
  • Watch the water meter — if it moves, water is going somewhere it should not
  • Compare the bill with the same month last year, and note the date of the jump
  • Take a photo of the meter reading
  • Call for slab leak detection — meter, pressure, listening, location

Call Now

Causes

What causes it

Supply line leak under the slab

The usual cause: a pipe leaking under the concrete sends metered water into the soil.

Running toilet or dripping tap

A toilet that runs or a tap that drips moves the meter too — turn them off before the test.

Irrigation system leak

A leak in the irrigation system runs outside the house and moves the meter without wetting a floor.

Water heater or appliance leak

A leaking water heater or appliance hose can raise the bill before any floor shows water.

Signs

Signs of this problem

  • A water bill that jumps in one month with no change in use
  • A water meter that moves with every tap off
  • A bill that creeps up month after month
  • A damp patch on the floor that appeared with the bill jump
  • The sound of running water when every tap is off
  • A warm spot on the floor, on a hot line
  • Low water pressure that arrived with the bill jump

Related service: Slab Leak Detection

Related guide: Signs of a slab leak in McKinney

Related service: Slab Leak Detection

Questions

Frequently asked questions

Questions people ask about unexplained high water bill, answered plainly.

It may be. A bill that jumps in one month, with no change in use, is a leak until proven otherwise. The meter test decides it: turn off every tap and appliance, then watch the meter. If it keeps moving, water is going somewhere it should not, and the leak is on your side of the meter.

The meter is usually in a box near the street or on the side of the house. Turn off every tap, toilet, washing machine, ice maker and irrigation system, then watch the dial. If it keeps moving, water is going somewhere it should not. Take a photo of the reading for your records.

Yes. A toilet that runs, a tap that drips, or an irrigation system that leaks can all move the meter and raise the bill. Turn them all off before the meter test, so the test reads the pipes and not the fixtures.

Then the leak is not on the supply side. The investigation turns to the drain side — a camera in the drain line, or a smoke test — because a drain leak does not move the meter. A running toilet or a dripping tap is checked the same way.

Some providers offer a leak adjustment, and the record matters: the bills that show the jump, the date it started, and the meter readings and report from the detection visit. Keep the bills, the photos, and the report together.

That depends on the size of the leak, and it is not measured in figures on this site. A small leak runs for weeks before the floor shows anything, and the bill is the record of it. The meter test with every tap off is the check that confirms it.

Dealing with this problem now?

Call Now to reach a local slab leak professional. Describe the problem, where it is, and what it has touched.

Call Now

Contact

Call now for slab leak help

Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

Call Now

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the damp floor, the water meter, and the rooms affected.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the signs started, and whether the water meter moves when every tap is off.
McKinney Slab Leak Pros — helper
☎ Call Now