Under-Slab Leak Repair in McKinney, TX
Once a leak is located, the pipe has to be reached — through the floor above it, or by tunnelling underneath from outside. The method follows the leak, the pipe, and the condition of the rest of the line.
Need help with a slab leak?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
What this service does
Under-slab repair is the part of the job most homeowners worry about, because it involves the floor. The worry is understandable: the floor is the most visible part of the house, and opening it sounds like a large job. In practice the opening is small, because detection has already marked the leak — a small area of floor, usually no bigger than a dinner plate, over the exact spot where the pipe is leaking.
There are two ways to reach a leaking pipe under a slab. The first is through the floor: a small section of flooring and concrete is opened over the marked leak, the damaged section of pipe is cut out and replaced, and the floor is put back. The second is tunnelling: a small tunnel is dug under the slab from outside the house, the pipe is reached from underneath, and the floor inside is never opened. Both methods fix the same leak. The choice between them follows the leak location, the pipe, and the room above it.
Through-the-floor repair is the usual choice when the leak sits under a room where the flooring can be opened and put back cleanly — a hallway, a living room, a bedroom. The opening is small, the work is direct, and the repair is visible and testable before the floor is closed. Tunnelling is the usual choice when the leak sits under a bathroom or kitchen, where the floor holds tile, fixtures and cabinets that would be costly to disturb, or under a slab that should not be cut — a post-tension slab, for example, where cutting the concrete can damage the tension cables inside.
The repair itself is straightforward once the pipe is reached. The damaged section is cut out, a new section is joined in, and the line is pressure-tested before anything is closed. The test matters: a repair that is not pressure-tested is a guess, and the meter test afterwards — with every tap off — is the check that the leak is fixed. If the meter still moves, there is another leak, and the detection work starts again.
One thing people get wrong about under-slab repair is assuming the smallest opening is the right one. Through the floor is usually the smaller job, but it is not always the right job — under a bathroom, the cost of disturbing tile and fixtures can be larger than the tunnel. And a spot repair is not always the right repair at all: if the line has leaked before, or if it is in poor condition along its length, repiping the line through the walls and attic is the repair that lasts. The location report is what decides it.
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.
How under-slab leak repair works in a McKinney home
The job starts with the detection report: the leak location marked on the floor, the line identified, and the condition of the rest of the line noted. The crew checks the slab type first — post-tension or conventional — because that decides whether the concrete can be cut. A post-tension slab holds steel cables under tension inside the concrete, and cutting through one can damage the slab. In a post-tension home, tunnelling is usually the safer route.
For a through-the-floor repair, the flooring over the marked spot is lifted and a small section of concrete is opened. The pipe is exposed, the damaged section is cut out, and a new section is joined in with the right fittings for the pipe material — copper, PEX, or CPVC. The line is pressure-tested while it is still open, so a bad joint is caught before the floor is closed. Then the concrete is patched, the flooring is put back, and the meter is checked with every tap off.
For a tunnelling repair, a small entry is dug outside the house, usually near the foundation, and a tunnel is dug under the slab to the leak. The work happens underneath, so the floor inside is never opened and the room above stays usable. The pipe is repaired the same way — damaged section out, new section in, pressure test — and the tunnel is backfilled when the work is done. Tunnelling takes longer than opening the floor, and it needs room outside the house to dig, but it leaves the inside of the home untouched.
What the service includes
Slab type check
Whether the slab is post-tension or conventional is checked first, because it decides whether the concrete can be cut.
Through-the-floor repair
A small section of flooring and concrete is opened over the marked leak, the damaged section is replaced, and the floor is put back.
Tunnelling repair
A small tunnel is dug under the slab from outside, the pipe is repaired from underneath, and the floor inside is never opened.
Pipe replacement
The damaged section is cut out and a new section is joined in, with fittings matched to the pipe material.
Pressure test before closing
The repaired line is pressure-tested while it is still open, so a bad joint is caught before the floor is closed.
Meter check after repair
The meter is checked with every tap off after the repair, to confirm the leak is fixed and no second leak is hiding.
How the work runs
Detection report first
The leak location is marked on the floor, the line is identified, and the slab type is checked.
Choose the method
Through the floor, or tunnelling underneath — the leak location, the room above, and the slab type decide.
Reach the pipe
A small section of floor is opened, or a tunnel is dug from outside the house to the leak.
Replace the damaged section
The failed section is cut out and a new section is joined in, with fittings matched to the pipe.
Pressure test
The repaired line is tested while it is still open, before anything is closed.
Close and check
The concrete is patched or the tunnel is backfilled, the flooring is put back, and the meter is checked with every tap off.
Tools and methods used
Concrete saw and breaker
Opens a small, controlled section of slab over the marked leak for a through-the-floor repair.
Tunnelling shoring
Supports the tunnel dug under the slab so the pipe can be reached safely from underneath.
Pipe cutter and fittings
Cuts out the damaged section and joins in the new section, matched to the pipe material.
Pressure test gauge
Verifies the repaired line holds pressure before the floor is closed or the tunnel is backfilled.
Through the floor vs tunnelling
Through the floor is the direct route: the opening is small, the pipe is visible, the repair is testable, and the work is usually done in a day. It suits leaks under rooms where the flooring can be lifted and put back cleanly. The trade-off is the floor itself — tile, wood, or carpet over the opening has to be disturbed, and matching it afterwards takes care.
Tunnelling is the indirect route: the pipe is reached from underneath, the floor inside is never opened, and the room above stays usable. It suits leaks under bathrooms and kitchens, under post-tension slabs, and under rooms where the flooring cannot be disturbed. The trade-off is time and access — the tunnel has to be dug, the work happens in a confined space, and there has to be room outside the house to dig. Neither method is better in general; the leak location decides.
When a spot repair is not enough
A spot repair fixes one leak in one place. It is the right repair when the line is otherwise sound — a single failure at a joint, a fitting that gave way, a section that was damaged during construction. It is not the right repair when the line has leaked before, or when the detection report shows the line is in poor condition along its length. In clay soil, a line that has failed once can fail again a few feet away, and a second opening in the same floor is a second disruption.
That is the point at which repiping enters the conversation. A repipe replaces the failing under-slab lines with new lines run through the walls and attic, so no more pipe sits in the soil under the slab. It is a larger job than a spot repair, but it is one job instead of several, and it is the repair that makes sense when the line itself is the problem rather than one spot on it.
A leaking pipe buried under the slab
A leak under the slab keeps running — washing out soil, lifting flooring, and stressing the foundation.
The damaged section replaced and pressure-tested
The leak is located with listening and electronic equipment before any concrete is opened.
Problems under-slab leak repair solves
- A single leak in an otherwise sound line
- A leaking joint or fitting under the slab
- A leak under a bathroom or kitchen floor
- A leak under a post-tension slab that cannot be cut
- A pipe damaged during construction, now leaking years later
- A leak that has washed out soil from under the slab
Signs you need under-slab leak repair
- A leak has been located under the slab by detection
- A warm patch on the floor that detection traced to a hot line
- A damp patch on the floor over a marked leak location
- A water bill that jumped, with the leak pinpointed underneath
- The sound of running water under the floor
- Flooring lifting over a spot where water is coming up
- A meter that moves with every tap off, and a located leak
- A previous repair on the same line, now leaking again nearby
Related problems
Damp floor or carpet · Foundation cracks · Warm spot on the floor
Industries that use this service
Rental Properties · Apartments & Condos · Retail Shops · All industries →
Frequently asked questions
Questions people ask about under-slab leak repair, answered plainly.
Small. Detection marks the leak to a small area — usually no bigger than a dinner plate — and the opening is made over that spot only. The concrete is not opened to search for the leak; the search happens first, from above the floor.
Neither is better in general. Through the floor is the direct route and usually the smaller job; tunnelling leaves the inside of the home untouched and suits leaks under bathrooms, kitchens, and post-tension slabs. The leak location, the room above, and the slab type decide.
Cutting a post-tension slab is a risk, because the slab holds steel cables under tension inside the concrete, and cutting through one can damage the slab. In a post-tension home, tunnelling is usually the safer route, and the slab type is checked before any cutting is planned.
A through-the-floor spot repair is usually one visit after detection. Tunnelling takes longer, because the tunnel has to be dug and the work happens underneath. The detection report and the method decide the schedule, and both are known before the work starts.
The flooring over the opening is lifted and put back, and matching it takes care — tile, wood, and carpet each have their own method. The opening is kept small so the repair area is small too.
That is the question the detection report answers. If the line is in poor condition along its length, or if it has leaked before, repiping the line through the walls and attic is the repair that lasts — one job instead of several openings in the same floor.
Yes. The repaired line is pressure-tested while it is still open, before the floor is closed or the tunnel is backfilled. The meter is then checked with every tap off, to confirm the leak is fixed.
No. The repair fixes the pipe. If the leak washed out soil or the slab has moved, that is a separate question, answered after the leak is fixed — not before. Detection first, pipe repair second, foundation questions third.
Slab leak in your McKinney home?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Call now for slab leak help
Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.