McKinney & the DFW metro · Slab leak helpMon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Faq McKinney, TX
Home › FAQ

Slab Leak Questions, Answered

Every question answered on this site, in one place — what to do first, how detection works, what insurance covers, and how to spot a slab leak.

FAQ

All questions

Detection work is scoped by the visit, not by a list of figures — the size of the home, the number of lines, and the methods needed all shape it. The visit itself is what you are paying for: meter and pressure tests, acoustic listening, line location, and a marked location with a report.

Most detection visits take a few hours. The meter and pressure tests are quick; the listening work takes longer, because the operator has to work across the floor and confirm the loudest point from more than one angle. A home with two leaks, or a leak that is hard to hear through thick flooring, takes longer.

Yes — that is the point of detection. Acoustic listening, electronic line location, thermal imaging and tracer gas all work from above the floor. The concrete is opened only after the leak is located, and only over the marked area.

Some leaks are quiet — a slow drain-line leak, or a leak under thick stone flooring. When listening alone is not enough, the crew adds methods: tracer gas in the line, a thermal camera for hot lines, or a camera in the drain line. The methods stack until the location is confirmed.

Yes. The report records the leak location, the line, the meter readings and the pressure test results — the same record an insurer asks for. Keep the photos and the readings with the report, and note the date the signs started.

Yes. A home can have a hot line leak and a cold line leak, or a supply leak and a drain leak. That is why the meter is checked again after every repair — a meter that still moves means there is more to find.

Yes. A wet floor shows where the water came up, not where the pipe is leaking — water travels under the slab before it surfaces. Detection finds the pipe, so the repair opens the floor in the right place.

No. Detection works from above the floor — listening, location, thermal imaging and meter tests. The floor is opened only for the repair, and only over the marked leak area.

Shut off the main water supply if it is safe to do so, move valuables off wet floors, stay away from wet outlets and switches, take photos of the water and the meter, and call for help. Do not wade through water to reach a shutoff if the water is near electricity.

Shutting off the main supply stops the leak immediately — that is the first move, and it is one a homeowner can usually do. The detection and repair that follow take longer, but the water stops running the moment the supply is off.

Yes. The repair itself — spot repair, tunnelling, or repiping — is the same. The difference is the order: in an emergency the water is stopped first, then detection finds the leak. In a planned visit, detection comes first and the water is stopped as part of the repair.

Only over the marked leak area, and only after detection has located it. The concrete is not opened to search for the leak — the listening and location work happens first, from above the floor.

Leaks under wet rooms are common, because that is where the lines run. The repair opens the floor in that room, over the marked spot. Fixtures are moved only if they sit directly over the leak, and the work is planned around them.

The repair itself is scoped the same way — by the leak location, the pipe, and the method. What changes in an emergency is the timing: the water is stopped first and the work starts sooner. The scope of the repair does not change because the leak is running.

Running water washes out soil from under the slab, and a slab with washed-out soil underneath can settle or crack. After the pipe is fixed, the floor is checked and the wet areas are dried. If the slab has moved, that is a separate question — and it is answered after the leak is fixed, not before.

Stop the water first, then call for slab leak detection. A foundation problem and a slab leak can look alike, and fixing the foundation while a pipe is still leaking under it wastes the work. Detection first, then the repair decision.

Small. Detection marks the leak to a small area — usually no bigger than a dinner plate — and the opening is made over that spot only. The concrete is not opened to search for the leak; the search happens first, from above the floor.

Neither is better in general. Through the floor is the direct route and usually the smaller job; tunnelling leaves the inside of the home untouched and suits leaks under bathrooms, kitchens, and post-tension slabs. The leak location, the room above, and the slab type decide.

Cutting a post-tension slab is a risk, because the slab holds steel cables under tension inside the concrete, and cutting through one can damage the slab. In a post-tension home, tunnelling is usually the safer route, and the slab type is checked before any cutting is planned.

A through-the-floor spot repair is usually one visit after detection. Tunnelling takes longer, because the tunnel has to be dug and the work happens underneath. The detection report and the method decide the schedule, and both are known before the work starts.

The flooring over the opening is lifted and put back, and matching it takes care — tile, wood, and carpet each have their own method. The opening is kept small so the repair area is small too.

That is the question the detection report answers. If the line is in poor condition along its length, or if it has leaked before, repiping the line through the walls and attic is the repair that lasts — one job instead of several openings in the same floor.

Yes. The repaired line is pressure-tested while it is still open, before the floor is closed or the tunnel is backfilled. The meter is then checked with every tap off, to confirm the leak is fixed.

No. The repair fixes the pipe. If the leak washed out soil or the slab has moved, that is a separate question, answered after the leak is fixed — not before. Detection first, pipe repair second, foundation questions third.

When the line has leaked more than once, or when the detection report shows it is failing along its length. One leak in a sound line is a spot repair. Two leaks on the same line, or a line that loses pressure along its length, means the line itself is the problem — and repiping is the repair that lasts.

Longer than a spot repair — the new lines have to be run through the whole house, and every fixture has to be reconnected and tested. The schedule depends on the size of the home and the number of fixtures, and it is known before the work starts, from the repipe plan.

The water is off while the changeover happens — when the old lines are capped and the new lines take over. The new lines are run first, while the old lines are still in place and the water is still on, so the outage is kept to the changeover itself.

They are capped and left in place. Digging them out would mean opening the slab for no reason, so they stay where they are, empty and sealed. Nothing new goes under the slab.

Usually PEX, a flexible pipe that bends with movement instead of resisting it, or CPVC. The choice follows the house, the water, and the layout. Older homes often have copper under the slab — durable, but rigid, and rigid pipe is what soil movement punishes.

No. Repiping replaces the water lines. If the slab has moved or the foundation needs attention, that is a separate question, answered after the pipe work — not before. The repipe stops the leaks that wash out soil; it does not undo movement that has already happened.

No. A repipe covers the supply lines — hot and cold water to every fixture. Drain and sewer lines run under the slab too, and they are a different system with their own detection and repair.

Walls are opened at fixture points — behind sinks, showers, toilets and the washing machine — where the new pipe has to reach a fixture. The openings are small and local, and they are patched when the work is done.

The meter test is the check that separates them. Turn off every tap and appliance, then watch the water meter — if it keeps moving, water is going somewhere it should not, and that is a leak until proven otherwise. A meter that holds still points to the soil. The detection visit runs that test, then locates any leak it finds.

Yes. Water under the slab washes out the soil that supports it, and a slab with washed-out soil underneath can settle or crack. A leak can also soak the clay on one side of the house, and wet clay swells — so the slab heaves on the wet side. In both cases the leak is the cause and the movement is the effect.

The leak first. Fixing the foundation while a pipe is still leaking under it wastes the work — the water keeps washing out soil, and the slab keeps moving. Detection first, pipe repair second, foundation questions third.

It records the meter readings, the pressure test results, the leak location if there is one, and the pattern of the symptoms — and it states, plainly, whether the evidence points to a leak, to clay movement, or to both. That report is what the next decision is made from.

Soil movement and sudden pipe failure are usually treated differently by a homeowners policy, which is why the detection report matters — it separates the water damage from the soil movement with readings. Check your policy and keep the report with the photos and the meter readings.

That pattern points to the soil: the clay swells in a wet season and shrinks in a dry one, and the house moves with it. A leak does not follow the seasons — it starts when the pipe fails and gets worse while it runs. If the pattern is seasonal and the meter holds still, the soil is the likely cause.

Yes, and it is common in McKinney. A leak soaks the clay on one side of the house and the slab heaves there, or a leak washes soil out and one corner settles. The detection report says whether the evidence points to a leak, to clay movement, or to both — and the leak is fixed first either way.

No. This service finds and fixes the leak. If the report points to clay movement, the next step is a foundation specialist — and the report goes with you, so the cause is already separated from the soil.

The meter test is the check. Turn off every tap and appliance, then watch the water meter — if it keeps moving, water is going somewhere it should not, and the leak is on the supply side. If the meter holds still, the leak is more likely on the drain side, or a running toilet or dripping tap.

A warm floor points to the hot line; a bill that jumped with no warm floor points to the cold line. The lines are pressure-tested separately to confirm which one is leaking, because the repair for each can be different — and because a hot line leak can look like a water heater problem.

A home can have two leaks — a supply leak under the slab and another in a wall, or a supply leak and a drain leak. That is why the meter is checked again after every repair: a meter that still moves means there is more to find.

Because the water goes into the soil under the slab, not onto the floor. A small supply leak can run for weeks before the floor shows anything — and the bill is the first sign. The meter test with every tap off is the check that confirms it.

No. Low pressure can come from a municipal issue, a closed valve, or a clogged line. If neighbours have normal pressure and yours has dropped, and the meter moves with every tap off, a leak is a likely cause — and the pressure test confirms it.

Under the slab is the most common place, because much of the supply route runs there and the Houston Black clay moves with every wet and dry season. Joints and fittings are the usual failure points. Leaks also happen in walls and attics, at fittings behind fixtures.

Yes. A hot line leak can look like a water heater problem, and the two have to be separated before any work is planned. The water heater is checked as part of the hot line test.

Then it is not a house leak. A meter that holds still with everything off, or a leak visible between the street and the meter, points to the city side — and the water provider is the call to make. The meter test is what separates the two.

The meter test is the check. Turn off every tap and appliance, then watch the water meter — if it holds still, the supply lines are sound, and the leak is more likely on the drain side. A damp floor that appears after use, odours, and slow drains point the same way. The camera confirms it.

The camera shows the inside of the drain line: cracks, breaks, separated joints, roots, or a belly where the pipe has settled and water pools. The camera has a locator on it, so the picture is matched to a point on the floor above — the break is located before any concrete is opened.

Sewer water is treated as contaminated water. Keep people and pets away from wet areas, do not run taps or flush while the leak is being investigated, and do not clean it up with household tools. The cleanup after a sewer leak is handled as contaminated-water work.

Harmless smoke is blown into the drain system, and it escapes through any break or open joint — showing up above the floor, at a roof vent, or through a crack in the slab. The smoke test finds leaks the camera cannot see, and it confirms the location the camera pointed to.

Yes. Water escaping from a drain line soaks the clay under the slab, and wet clay swells — or washes out, and the slab settles. A sewer leak and a foundation problem can look alike, which is why the leak is found and fixed before any foundation questions are answered.

Not always. Cast iron corrodes from the inside, and the camera shows how far it has gone — a single break is a repair, a line that is thin along its length is a replacement. The camera report, not the age alone, decides it.

Only over the marked break, and only after the camera has located it. Sewer repairs are often done by tunnelling, because the line runs deeper and the work is messier — but the location is always confirmed first, from above the floor.

Because a drain leak runs only when water goes down the drain. A shower, a flush, a washing machine cycle — each one sends water through the break, and the floor is damp after use and drier in between. A supply leak, by contrast, runs all the time, because the line is always under pressure.

Yes. McKinney sits on Houston Black clay, an expansive soil that moves with every wet and dry season, and most homes sit on slabs with water lines underneath. A slab leak check — meter test, floor walk, and a written report — belongs on the list before closing, alongside the general home inspection.

Usually not in depth. A general inspection covers the visible house — roof, structure, electrical, appliances. A slab leak inspection covers the invisible part: the water lines under the slab, tested with the meter and listened to through the floor. The two belong together.

Then the buyer knows before closing, while there is still leverage — a leak found before closing is a repair the seller addresses, or a price the buyer adjusts. The report records the location and the condition of the line, so the negotiation has evidence.

Then the report says so, and the buyer keeps it as a record. A clean report does not promise that no leak will ever happen — a line that is sound today can fail tomorrow in clay soil — but it is a reading of the house as it stands, on the day of the inspection.

Yes. New lines fail less often, but construction damage, a stressed joint, or a line laid in poorly compacted fill can fail early. New does not mean checked, and the meter test reads the same in a new home as in an older one.

Usually a few hours. The meter test is quick; the floor walk takes longer, because every room is checked; and if the meter moves, the listening work follows. The report is written the same day.

The buyer. It is written to be read by someone who is not a plumber: meter readings, signs found, leak location if any, and a plain statement of what the evidence means. The buyer takes it into the negotiation, or keeps it as a record.

Yes — more so, because a rental has a tenant living with the leak and a landlord who owns the building. A leak found before closing is a repair the seller addresses; a leak found after closing is the new owner's repair, with a tenant living over it.

A warm patch on a tile or wood floor usually points to a hot water line leaking under the slab. The hot water escapes the pipe, warms the soil and the concrete above it, and the heat comes up through the floor. The floor feels warm in one spot while the rest of the floor is cool.

Usually, but not always. A floor can feel warm above a heating vent, a sunlit patch, or a hot water line that is sound. The test is the hot line pressure test: a hot line that loses pressure is leaking. The thermal camera and the pressure test together confirm it.

It may be replacing hot water that is leaking away under the floor. A hot line leak sends hot water into the soil, and the heater works to replace it — so it runs more than it should. The hot line pressure test separates a line leak from a heater problem.

By heat and sound. A thermal camera reads the floor and shows the warm area above the leak, and acoustic listening follows the sound of escaping water to its loudest point. The hot and cold lines are pressure-tested separately to confirm the leak is on the hot side.

The repair follows the same choice as any slab leak: spot repair through the floor, tunnelling underneath, or a reroute through the walls and attic if the line is in poor condition. The difference is the detection — heat is used as well as sound.

Yes. Once the hot water stops leaking under the slab, the soil and the concrete cool, and the floor returns to the temperature of the rooms around it. The cooling takes time — the slab holds heat — but the warm patch does not return.

Yes. Hot water under the slab soaks the clay, and wet clay swells — so the slab can heave on the wet side. Running hot water can also wash out soil. The leak is fixed first, and any foundation questions are answered after, not before.

Not usually. A hot line leak is a pipe problem, not a heater problem — and the heater is checked as part of the job to separate the two. If the heater is failing on its own, that is a separate question, and the check says so.

Usually, but not always. A floor can feel warm above a heating vent, in a sunlit patch, or above a sound hot water line. The test is the hot line pressure test: a hot line that loses pressure is leaking. The thermal camera and the pressure test together confirm it.

Warm, not hot — a clear difference from the floor around it, but not a burn. The warm area is often roughly circular, a few feet across, and it stays warm all day, because the leak runs all the time.

Yes. Once the hot water stops leaking under the slab, the soil and the concrete cool, and the floor returns to the temperature of the rooms around it. The slab holds heat, so the cooling takes time — but the warm patch does not return.

Shut off the main water supply if it is safe to do so — that stops the leak at its source. The water heater can be turned off as well, but the main supply is the first move. Do not wade through water to reach a shutoff if the water is near electricity.

A heater that runs constantly can be replacing leaked hot water, or it can be failing on its own. The two are separated by the tests: the hot line is pressure-tested on its own, and the heater is checked on its own. A warm floor points to the line.

By heat and sound. A thermal camera reads the floor and shows the warm area, acoustic listening follows the sound of escaping water, and the hot line is pressure-tested on its own. When the methods agree, the leak is marked on the floor.

It may be. A bill that jumps in one month, with no change in use, is a leak until proven otherwise. The meter test decides it: turn off every tap and appliance, then watch the meter. If it keeps moving, water is going somewhere it should not, and the leak is on your side of the meter.

The meter is usually in a box near the street or on the side of the house. Turn off every tap, toilet, washing machine, ice maker and irrigation system, then watch the dial. If it keeps moving, water is going somewhere it should not. Take a photo of the reading for your records.

Yes. A toilet that runs, a tap that drips, or an irrigation system that leaks can all move the meter and raise the bill. Turn them all off before the meter test, so the test reads the pipes and not the fixtures.

Then the leak is not on the supply side. The investigation turns to the drain side — a camera in the drain line, or a smoke test — because a drain leak does not move the meter. A running toilet or a dripping tap is checked the same way.

Some providers offer a leak adjustment, and the record matters: the bills that show the jump, the date it started, and the meter readings and report from the detection visit. Keep the bills, the photos, and the report together.

That depends on the size of the leak, and it is not measured in figures on this site. A small leak runs for weeks before the floor shows anything, and the bill is the record of it. The meter test with every tap off is the check that confirms it.

Because the water has a source below the floor. A spill dries and stays dry; a slab leak sends water up through the slab all the time, so the floor is damp again a few hours after mopping — in the same place, the same shape, a little larger each time.

Not always. A spill, an appliance hose, or a roof leak can wet a floor too. The test is the return: a spill dries and stays dry, a leak comes back. The meter test with every tap off is the check that confirms it.

You can mop up the water on the surface, but the leak underneath keeps running, so the floor will be damp again. The leak has to be found and fixed first — drying alone does not stop it. Wet flooring is lifted where it cannot dry in place, after the repair.

Not long. The EPA notes that mold can begin to grow on damp surfaces within 24 to 48 hours, and carpet padding holds water for days. A damp floor that stays damp is a job for detection, not for waiting.

Not necessarily. A damp patch means water is coming up through the slab. Whether the slab has moved is a separate question, answered after the leak is found and fixed — not before. Detection first, pipe repair second, foundation questions third.

Carpet padding holds water for days, and a carpet that feels dry on top can still be wet underneath. A moisture meter reads through the carpet to map how far the water has travelled, and the wet padding is lifted where it cannot dry in place.

No. In McKinney, the usual cause is the soil: Houston Black clay swells when wet and shrinks when dry, and that movement cracks floors and walls. A slab leak can cause the same symptoms, which is why the meter test is run — it separates a leak from clay movement.

By pattern and by meter. A leak is local — one damp patch, one warm spot, one crack near the wet area — and it shows up on the meter. Clay movement is broad — cracks in several rooms, doors sticking on more than one side — and it does not move the meter. A crack that opens in summer and closes in winter is the soil.

The leak first. Fixing the foundation while a pipe is still leaking under it wastes the work — the water keeps washing out soil, and the slab keeps moving. Detection first, pipe repair second, foundation questions third.

Yes. A leak soaks the clay on one side of the house, and wet clay swells — so the slab heaves on the wet side while the dry side stays put. A leak can also wash soil out, and the slab settles. Both are leak effects, and both are fixed by finding the pipe first.

It records the meter readings, the pressure test results, the leak location if there is one, and the pattern of the symptoms — and it states, plainly, whether the evidence points to a leak, to clay movement, or to both. That report is what the next decision is made from.

No. This service finds and fixes the leak. If the report points to clay movement, the next step is a foundation specialist — and the report goes with you, so the cause is already separated from the soil.

No. Low pressure can come from a municipal issue, a closed valve, a failing pressure regulator, or a clogged line. If neighbours have normal pressure and yours has dropped, and the meter moves with every tap off, a leak is a likely cause — and the pressure test confirms it.

Because the leak is on the main supply line, before it splits to the fixtures. A single weak tap is usually a fixture problem; the whole house going weak points to the line that feeds them all.

Yes. Even a small leak loses water before it reaches the taps, and the pressure drops. A large leak drops it more. The size of the drop gives a sense of the size of the leak, and the pressure test measures it.

Then the problem is on the city side — a main break, maintenance, or a supply issue — and the water provider is the call to make. A leak on your side of the meter lowers your pressure only, not the street's.

Not necessarily. Low pressure means water is escaping somewhere, and the leak is usually small and steady rather than a burst. A burst shows up differently — water on the floor, a meter spinning fast. Either way, the meter test is the check.

By meter, pressure, listening, and location. The meter test confirms the leak, the pressure test identifies the line, acoustic listening finds the leak through the floor, and electronic line location traces the pipe. The leak is marked before any work is planned.

Usually, yes. When every tap is off, the house should be quiet. A rushing or hissing sound with everything off means water is moving somewhere it should not — and in a McKinney home on a slab, the most likely place is a pipe under the floor. The meter test confirms it.

Yes. A toilet that runs sounds like water running in another room. Check every toilet, tap, and appliance first, turn them all off, and then watch the meter. A sound with a moving meter is a supply leak; a sound with a still meter is a fixture or a drain.

Near the leak. The sound travels through the pipe and the concrete, and it is loudest above the break. The operator follows the sound across the floor with a microphone, and the loudest point marks the leak.

An intermittent sound can be a toilet refilling, an appliance cycling, or a leak that runs only when the line is pressurised a certain way. Note when the sound appears and whether the meter moves at the same time — the two together are the diagnosis.

You can hear that something is running, but the equipment is what locates it. A ground microphone hears the sound through concrete and narrows it to a small area — the ear hears the house, the microphone hears the leak.

It depends on the meter. A sound with a meter spinning fast is a leak running now — shut off the main supply if it is safe and call for help. A sound with a meter moving slowly is urgent, but it can wait for a detection visit. The meter test decides it.

A slab leak in your McKinney home?

Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.

Call Now

Contact

Call now for slab leak help

Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

Call Now

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the damp floor, the water meter, and the rooms affected.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the signs started, and whether the water meter moves when every tap is off.
McKinney Slab Leak Pros — helper
☎ Call Now