McKinney & the DFW metro · Slab leak helpMon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Tracer gas leak detection McKinney, TX hero
Home › Services › Tracer Gas Leak Detection

Tracer Gas Leak Detection in McKinney, TX

Some leaks are too quiet to hear. Tracer gas detection puts a harmless gas into the pipe, and a sensor above the floor finds where it escapes — the leak, found by gas.

Call Now

McKinney & the DFW metroDetection, location & repairPinpoint location before any digging

Need help with a slab leak?

Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.

Call Now

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

1
Shut the water off firstThe main supply stops the leak at its source — if you can reach it safely.
2
Pinpoint the leakListening equipment and electronic location find the leak before any concrete is opened.
3
Repair under the slabSpot repair, tunnelling, or repiping — the method follows the leak, not the other way round.
4
Document everythingPhotos, meter readings and notes help when you talk to your insurer.
Tracer Gas Leak Detection

What this service does

Tracer gas detection is the method for leaks that acoustic listening cannot find. A slow leak makes little sound. A leak under thick stone flooring is muffled. A leak in a line that runs deep, or behind a wall of fixtures, can be hard to hear from the floor above. In those cases the crew adds a second sense: a harmless gas is put into the pipe, and a sensor above the floor finds where it escapes.

The gas is a mix of hydrogen and nitrogen — hydrogen because its molecules are tiny and escape through the smallest break, nitrogen because it carries the hydrogen safely. The mix is inert at the concentration used, and it is put into the line after the water is drained from it. The gas fills the pipe, escapes through the break, and rises through the soil and the slab to the floor above — where a sensitive sensor, worked across the floor, reads the concentration and follows it to its highest point.

The method is precise, and it is slow. The sensor is worked across the floor in a grid, like the acoustic microphone, and the readings are compared point by point. The highest reading marks the leak. The gas has to be given time to travel — through the soil, through the slab, to the surface — so the work takes longer than listening alone. But for a quiet leak, it is the method that finds what the microphone cannot hear.

Tracer gas is also the method for confirming a location. A leak that acoustic listening placed in one spot, and thermal imaging placed in another, is settled by the gas: the sensor reads the gas, and the highest reading is the leak. The methods stack, and the gas is the one that is hardest to argue with, because the gas can only come from the pipe it was put into.

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the damp floor, the water meter, and the rooms affected.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the signs started, and whether the water meter moves when every tap is off.

Call Now

Understanding

How tracer gas leak detection works

The visit starts with the meter and pressure tests, because the gas is only used once a leak is confirmed and the line is identified. The line is drained of water, and the gas mix is put in under low pressure. The gas fills the pipe and escapes through the break, rising through the soil and the slab to the floor above.

Then the sensor work starts. A sensitive gas sensor is worked across the floor in a grid, reading the concentration at each point. The readings are compared, and the highest reading marks the leak. The work is slow — the gas has to travel, and the sensor has to be given time at each point — but the reading is direct: the gas can only come from the pipe it was put into.

When the readings converge on one spot, the leak is marked on the floor and the report is written. The report records the line, the location, and the readings, and the repair plan is built from it. The gas is cleared from the line afterwards, and the water is put back — the gas leaves no trace in the pipe.

Tracer gas leak detection McKinney, TX 1
Tracer gas leak detection McKinney, TX 2
Tracer gas leak detection McKinney, TX 3
Included

What the service includes

Meter and pressure tests first

The leak is confirmed and the line is identified before any gas is used.

Line draining

The water is drained from the leaking line so the gas can fill it.

Gas fill

A harmless hydrogen and nitrogen mix is put into the line under low pressure.

Sensor survey

A sensitive sensor is worked across the floor in a grid, following the gas to its highest reading.

Leak marking and report

The leak is marked on the floor, and the report records the line, the location, and the readings.

Process

How the work runs

1

Confirm the leak

Meter and pressure tests confirm a leak exists and identify the line.

2

Drain the line

The water is drained from the leaking line so the gas can fill it.

3

Fill with gas

The hydrogen and nitrogen mix is put into the line under low pressure.

4

Survey with the sensor

The sensor is worked across the floor in a grid, following the gas to its highest reading.

5

Mark and report

The leak is marked on the floor and the report is written; the gas is cleared and the water is put back.

Tracer gas leak detection McKinney, TX process 1
Tracer gas leak detection McKinney, TX process 2
Tracer gas leak detection McKinney, TX process 3
Tracer gas leak detection McKinney, TX process 4
Tools & methods

Tools and methods used

Tracer gas mix

Hydrogen and nitrogen — hydrogen escapes through the smallest break, nitrogen carries it safely.

Gas sensor

A sensitive sensor that reads the gas concentration above the floor, point by point.

Pressure test gauge

Confirms the leak exists and identifies the line before the gas work starts.

Tracer gas leak detection McKinney, TX equipment
Tracer Gas Leak Detection

When tracer gas is used

Tracer gas is used when acoustic listening cannot find the leak — a slow leak, a leak under thick flooring, a leak that is hard to hear through the slab. It is also used to confirm a location when two methods disagree: the gas reading settles it, because the gas can only come from the pipe it was put into.

It is not the first method, because it takes longer than listening and it needs the line drained first. The usual order is meter, pressure, listening, location — and gas when the listening does not converge, or when the leak is too quiet to hear.

Problem

A leak too quiet to hear through the floor

A leak under the slab keeps running — washing out soil, lifting flooring, and stressing the foundation.

Solution

The leak found by gas and marked

The leak is located with listening and electronic equipment before any concrete is opened.

Problems solved

Problems tracer gas leak detection solves

  • A leak too quiet for acoustic listening
  • A slow leak under thick flooring
  • A leak that listening placed in one spot and imaging in another
  • A leak in a line that runs deep or behind fixtures
  • A location that needs confirming before any floor is opened

Call Now

Signs

Signs you need tracer gas leak detection

  • A meter that moves with every tap off, but no sound on listening
  • A damp patch with no loud leak sound
  • A leak suspected under thick stone flooring
  • Two detection methods pointing to different spots
  • A slow leak that has run for weeks
  • A previous detection visit that could not pinpoint the leak
Questions

Frequently asked questions

Questions people ask about tracer gas leak detection, answered plainly.

A harmless mix of hydrogen and nitrogen is put into the leaking pipe after the water is drained from it. The gas escapes through the break, rises through the soil and the slab, and a sensitive sensor above the floor finds where it escapes — the highest reading marks the leak.

Yes. The mix is inert at the concentration used. It is put into the line under low pressure, it leaves no trace in the pipe, and the water is put back after the work. The gas can only come from the pipe it was put into.

When the leak is too quiet to hear — a slow leak, a leak under thick flooring, or a leak that is hard to hear through the slab. It is also used to confirm a location when two methods disagree. The usual order is meter, pressure, listening, location — and gas when the listening does not converge.

Longer than listening alone. The gas has to travel through the soil and the slab, and the sensor has to be given time at each point. The work is slow, but the reading is direct — the gas can only come from the pipe it was put into.

No. The gas is cleared from the line afterwards, and the water is put back. The gas leaves no trace in the pipe.

No. Tracer gas is a supply-line method — the gas is put into a pressurised water line. Drain lines are not under pressure, and they are checked with a camera or a smoke test instead.

Slab leak in your McKinney home?

Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.

Call Now

Contact

Call now for slab leak help

Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.

Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET

Call Now

Before you call

  • Shut off the main water supply if it is safe to do so.
  • Move valuables, rugs and electronics off wet floors.
  • Take photos of the damp floor, the water meter, and the rooms affected.
  • Stay away from wet outlets, switches and light fixtures.
  • Note when the signs started, and whether the water meter moves when every tap is off.
McKinney Slab Leak Pros — helper
☎ Call Now