Thermal Imaging Leak Detection in McKinney, TX
A hot water line leaking under the slab warms the floor above it. A thermal camera reads that warmth and shows it as a bright patch — the leak, found by heat.
Need help with a slab leak?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
What this service does
Thermal imaging finds leaks by temperature. A camera reads the infrared radiation from a surface and turns it into a picture, where warmer areas show up bright and cooler areas show up dark. A hot water line leaking under a slab warms the soil, the concrete, and the floor above it — and the camera shows that warm area as a bright patch on the screen, against the cooler floor around it. The leak is found by heat, not by sound.
The method suits hot water lines, and it suits them well. A hot line leak is the slab leak you can feel — a tile floor that is warm in one spot while the rest of the floor is cool — and the camera makes that feeling visible, and measurable. The warm area is mapped, its edges are read, and the brightest point marks the leak. The picture is kept with the report, so the location is recorded as an image as well as a mark on the floor.
Thermal imaging has limits, and they are worth knowing. It finds hot leaks, not cold ones — a cold line leak does not warm the floor, and the camera will not see it. It reads the surface, not the pipe: a warm patch on the floor can come from a heating vent, a sunlit area, or a hot line that is sound. And the floor has to be visible — carpet, rugs, and furniture hide the surface the camera needs to read. That is why thermal imaging is used with acoustic listening and pressure tests, and the location is marked only when the methods agree.
In McKinney, thermal imaging is used most on the homes where hot line leaks are most common: 1990s homes with older copper hot lines, and homes where the water heater runs more than it should. A heater that works to replace leaked hot water is a sign, and the camera is the check that confirms it — a warm patch on the floor, with a hot line that loses pressure, is a leak found by two methods at once.
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.
How thermal imaging leak detection works
The visit starts with the meter and pressure tests, because the camera is only useful once a leak is confirmed and the line is identified. The hot and cold lines are pressure-tested separately — a hot line that loses pressure is leaking, and the camera work starts on that line. The water heater is checked too, because a hot line leak can look like a heater problem.
Then the camera is worked across the floor, room by room, reading the surface temperatures. The floor is cleared where it can be — rugs lifted, furniture moved — so the camera reads the floor itself, not the things on it. The warm area shows up as a bright patch, and its edges are mapped: the brightest point is the leak, and the shape of the patch shows how far the hot water has spread under the slab.
The picture is checked against the other methods. Acoustic listening follows the sound of escaping water to its loudest point, and the two should agree — the brightest point and the loudest point should be the same place. When they agree, the leak is marked on the floor and the report is written, with the thermal picture kept as part of the record.
What the service includes
Hot line pressure test
The hot line is tested on its own, to confirm the leak is on the hot side.
Water heater check
The heater is checked, because a hot line leak can look like a heater problem.
Thermal camera survey
The floor is read room by room, and the warm area above the leak is mapped.
Acoustic confirmation
Listening follows the sound of escaping water, and the two methods are checked against each other.
Leak marking and report
The leak is marked on the floor, and the thermal picture is kept with the report.
How the work runs
Confirm the hot line leak
Hot and cold lines are pressure-tested separately; the water heater is checked.
Clear the floor
Rugs are lifted and furniture moved, so the camera reads the floor itself.
Read the floor
The camera is worked across the floor, and the warm area is mapped.
Confirm by sound
Acoustic listening follows the sound, and the two methods are checked against each other.
Mark and report
The leak is marked on the floor, with the thermal picture kept as part of the record.
Tools and methods used
Thermal imaging camera
Reads surface temperatures on the floor and shows the warm area above a hot water line leak.
Acoustic ground microphone
Confirms the camera location by following the sound of escaping water.
Pressure test gauge
Confirms the leak is on the hot line before the camera work starts.
When thermal imaging works, and when it does not
Thermal imaging works on hot lines, and it works well on bare floors — tile, wood, and polished concrete read clearly. It does not work on cold lines, which do not warm the floor, and it reads poorly through carpet, rugs, and furniture. A warm patch can also come from a heating vent, a sunlit area, or a sound hot line — so the camera is never used alone. The pressure test confirms the leak, the camera locates it, and acoustic listening confirms the location.
The other limit is time. A slab holds heat, so a floor can stay warm for a while after a leak is fixed — and a floor can take time to warm up after a leak starts. The camera reads the floor as it stands, on the day of the visit, and the picture is read with that in mind.
A warm patch on the floor, cause unknown
A leak under the slab keeps running — washing out soil, lifting flooring, and stressing the foundation.
The warm area mapped and the leak marked
The leak is located with listening and electronic equipment before any concrete is opened.
Problems thermal imaging leak detection solves
- A warm patch on the floor with no visible source
- A hot water line leaking under the slab
- A water heater that runs more than it should
- A hot line leak that needs locating without opening the floor
- A warm floor that needs separating from a heating vent or sunlit patch
Signs you need thermal imaging leak detection
- A warm spot on the floor, usually tile or wood
- A floor that is hot in one spot while the rest is cool
- A water heater that runs constantly
- A bill that rises alongside the heater running more
- Hot water that runs out faster than it used to
- A damp patch on the floor that feels warm
Related problems
Warm spot on the floor · Damp floor or carpet · High water bill
Industries that use this service
Restaurants & Hospitality · Apartments & Condos · Rental Properties · All industries →
Frequently asked questions
Questions people ask about thermal imaging leak detection, answered plainly.
A thermal camera reads the temperature of the floor and shows warmer areas as bright patches. A hot water line leaking under the slab warms the soil, the concrete, and the floor above it — and the camera shows that warm area, with the brightest point marking the leak.
No. A cold line leak does not warm the floor, so the camera will not see it. Cold leaks are found by acoustic listening, line location, and tracer gas. Thermal imaging is a hot-line method.
Yes. A heating vent, a sunlit patch, or a sound hot water line can all warm a floor. That is why the camera is never used alone — the pressure test confirms the leak, and acoustic listening confirms the location.
Mostly. Carpet, rugs, and furniture hide the surface the camera needs to read, so they are lifted or moved where possible. Tile, wood, and polished concrete read clearly.
Yes. The picture is kept with the detection report, so the location is recorded as an image as well as a mark on the floor. It is part of the record the insurer asks for.
Yes. Once the hot water stops leaking under the slab, the soil and the concrete cool, and the floor returns to the temperature of the rooms around it. The slab holds heat, so the cooling takes time — but the warm patch does not return.
Slab leak in your McKinney home?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Call now for slab leak help
Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.