The short version
Problem: A spot repair fixes one leak in one place; a repipe replaces the failing lines with new lines through the walls and attic.
What to do: The decision is made from the detection report — the leak, the line, and its condition — not from a preference.
When to call: Call for detection first, and keep the report for the decision and the claim.
What a spot repair is
A spot repair fixes one leak in one place. The leak is located, a small area of floor is opened over the marked spot — or a tunnel is dug underneath from outside — the damaged section of pipe is cut out and replaced, and the line is pressure-tested before anything is closed. The opening is small, the work is direct, and the repair is usually done in a day. It is the right repair when the line is otherwise sound: a single failure at a joint, a fitting that gave way, a section that was damaged during construction.
The spot repair is also the smaller disruption. The floor is opened in one place, the rest of the house stays usable, and the water is off only while the repair is made. For a homeowner with one leak in a sound line, it is the repair that makes sense — and the detection report is what says the line is sound.
What a repipe is
A repipe replaces the failing under-slab lines with new lines run through the walls and attic, so no more pipe sits in the soil under the slab. The old lines are abandoned in place, capped and empty, and the new lines take over — from the main supply and the water heater to every fixture in the house. Nothing new goes under the slab. The soil can move as it likes; there is no pipe in it to stress.
The work is larger than a spot repair, and it is honest to say so. Walls are opened at fixture points, lines are run through the attic, and the water is off while the changeover happens. But it is one job instead of several, and it ends the cycle of leak, repair, leak again. For a homeowner who has already paid for two spot repairs on the same line, the arithmetic is plain.
How the decision is made
The decision is made from the detection report, not from a preference. One leak in a sound line, with the rest of the line testing well, is a spot repair. Two leaks on the same line, or a line that loses pressure along its length, is a repipe — the line itself is the problem, and fixing one spot on it leaves the next failure in place. Age matters too: a line that is twenty years old in Houston Black clay has been flexed by two decades of wet and dry seasons.
The report records the age, the material, and the test results, and the recommendation follows from those three things. A homeowner who has already had two spot repairs on the same line has already made the decision in practice — the repipe is the job that ends the cycle.
What the comparison misses
The comparison is usually framed as cost, and cost is the wrong frame — the scope depends on the leak, and the leak is not known until detection finds it. The right frame is the line: is this one failure, or is the line failing? A spot repair on a failing line is a repair that has to be done again. A repipe on a sound line is work that did not need doing. The detection report is what tells them apart.
The other thing the comparison misses is the floor. A spot repair opens the floor in one place; a second spot repair opens it again, a few feet away; a third opens it again. Each opening is a disruption, and each one has to be matched afterwards. A repipe opens walls at fixture points, once, and the floor is never opened at all. The disruption is different in kind, not just in size.
Related: Whole-Home Repiping · slab leak help in McKinney
Related guides
How Long Does Slab Leak Repair Take?
Detection is usually one visit; a spot repair is usually one more; tunnelling and repiping take longer. The location report decides the schedule.
What Affects Slab Leak Repair Cost
No figures here — but the factors that shape the scope are knowable: where the leak is, how it is reached, what the line looks like, and what the water touched.
Slab Leak Prevention for McKinney Homeowners
You cannot change the clay under your home — but you can keep its moisture even, watch the meter, and catch a leak early. Here is what works.
Frequently asked questions
Questions people ask about this topic, answered plainly.
From the detection report. One leak in a sound line is a spot repair. Two leaks on the same line, or a line that loses pressure along its length, is a repipe — the line itself is the problem. The report records the age, the material, and the test results, and the recommendation follows from those three things.
No. A repipe on a sound line is work that did not need doing. A spot repair is the right repair for one leak in a healthy line — smaller, faster, and less disruptive. The repipe is the right repair when the line itself is failing, and the detection report is what says so.
Yes. A spot repair fixes the leak that is running now, and the repipe decision can wait until the next leak — or until the report shows the line is failing. But each spot repair is an opening in the floor, and a line that has leaked twice has already made the decision in practice.
No. Walls are opened at fixture points — behind sinks, showers, toilets and the washing machine — where the new pipe has to reach a fixture. The openings are small and local, and they are patched when the work is done. The floor is never opened.
They are capped and left in place. Digging them out would mean opening the slab for no reason, so they stay where they are, empty and sealed. Nothing new goes under the slab.
They solve different problems. A spot repair on a sound line lasts as long as the line does. A repipe on a failing line lasts because the line is no longer in the soil. The question is not which lasts longer — it is which one matches the line.
Still have questions?
Call Now to reach a local slab leak professional — describe the water and the rooms it reached.
Call now for slab leak help
Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.