The short version
Problem: Detection is usually one visit, a spot repair is usually one more, and tunnelling or repiping takes longer.
What to do: The schedule is known before the work starts, from the detection report and the method it points to.
When to call: Call for detection first — the location decides the plan, and the plan decides the time.
Detection: usually one visit
Detection is usually one visit, and it usually takes a few hours. The meter and pressure tests are quick; the listening work takes longer, because the operator has to work across the floor and confirm the loudest point from more than one angle. A home with two leaks, or a leak that is hard to hear through thick flooring, takes longer — but the visit is still one visit, and the report is written the same day.
The report is what the schedule is built from. It records the leak location, the line, and the condition of the rest of the line — and the repair method follows from those three things. A schedule given before detection would be a guess; a schedule given after detection is a plan.
Spot repair: usually one visit after detection
A through-the-floor spot repair is usually one visit after detection. The flooring over the marked spot is lifted, a small section of concrete is opened, the damaged section is cut out and replaced, and the line is pressure-tested while it is still open. Then the concrete is patched, the flooring is put back, and the meter is checked with every tap off. The work is usually done in a day.
The drying that follows takes longer than the repair. Water that ran under the slab soaked the soil, the flooring, and the base of the walls, and that water has to come out. Wet flooring is lifted where it cannot dry in place, air is moved across the wet areas, and the moisture is checked with readings. The EPA notes that mold can begin to grow on damp surfaces within 24 to 48 hours, so the drying starts the same day as the repair.
Tunnelling: longer, and worth knowing why
Tunnelling takes longer than opening the floor, because the tunnel has to be dug and the work happens underneath. A small entry is dug outside the house, usually near the foundation, and a tunnel is dug under the slab to the leak. The pipe is repaired the same way — damaged section out, new section in, pressure test — and the tunnel is backfilled when the work is done. The extra time is the digging, and the extra time is why tunnelling is chosen when the floor cannot be disturbed — under a bathroom, a kitchen, or a post-tension slab.
The schedule for tunnelling is known before the work starts, from the detection report and the access outside the house. There has to be room to dig, and the tunnel has to reach the leak — and both are checked before the work is planned.
Repiping: the longest job, and one job instead of several
A whole-home repipe is the longest job of the three, because the new lines have to be run through the whole house and every fixture has to be reconnected and tested. The schedule depends on the size of the home and the number of fixtures, and it is known before the work starts, from the repipe plan. The water is off while the changeover happens — when the old lines are capped and the new lines take over — and the new lines are run first, while the old lines are still in place and the water is still on.
A repipe is one job instead of several. A line that has leaked twice, and is repaired by spot fixes twice, is three disruptions — two repairs and the leak that started them. A repipe is one disruption, and it ends the cycle. The time is longer, but the time is spent once.
What can delay the work
A second leak is the usual delay. A home can have two leaks, and the second one only shows up once the first is fixed and the meter is checked again — a meter that still moves means there is more to find, and the detection work starts again. Access is the other delay: a leak under a bathroom with fixtures over it, or a tunnel that needs room outside the house to dig, takes longer to reach. Both are known before the work starts, from the detection report — and both are why the report comes first.
Related: Under-Slab Leak Repair · slab leak help in McKinney
Related guides
Repiping vs Spot Repair for a Slab Leak
One leak in a sound line is a spot repair. A line that has leaked twice, or is failing along its length, is a repipe. The detection report decides.
What Affects Slab Leak Repair Cost
No figures here — but the factors that shape the scope are knowable: where the leak is, how it is reached, what the line looks like, and what the water touched.
What To Do First When You Suspect a Slab Leak
A warm floor, a damp patch, a bill that jumped? The first ten minutes decide how bad it gets. Here is what to do first, in order — and what not to do.
Frequently asked questions
Questions people ask about this topic, answered plainly.
Detection is usually one visit of a few hours, and a spot repair is usually one more visit after that. Tunnelling and repiping take longer. The schedule is known before the work starts, from the detection report and the method it points to — and the drying that follows is checked with readings, not by the calendar.
Usually, yes. A through-the-floor repair opens a small area, and the rest of the house stays usable. Tunnelling happens outside and underneath, so the inside stays usable. The water is off while the changeover happens, and the crew plans the work around the rooms that have to keep working.
It depends on how much water there was, what it soaked, and how long it ran. Drying usually takes days, with moisture readings checked along the way. The readings decide when materials are dry — not the calendar, and not a look at the surface.
Because a home can have two leaks, and the second one only shows up once the first is fixed. A meter that still moves with every tap off means there is more to find, and the detection work starts again. The meter test is repeated until it holds.
The usual reason is a second leak, or access — a leak under a bathroom with fixtures over it, or a tunnel that needs room outside to dig. Both are known before the work starts, from the detection report, and the schedule is adjusted from there.
When the line has leaked more than once, or the detection report shows it is failing along its length — yes. A repipe is one job instead of several, and it ends the cycle of leak, repair, leak again. The time is longer, but the time is spent once.
Still have questions?
Call Now to reach a local slab leak professional — describe the water and the rooms it reached.
Call now for slab leak help
Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.