Acoustic Leak Detection in McKinney, TX
Water escaping a pipe under a slab makes a sound — a hiss or a rush that the ear cannot hear through concrete, but a ground microphone can. Acoustic detection follows that sound to the leak.
Need help with a slab leak?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
What this service does
Acoustic leak detection is the core method of slab leak work, and it is worth understanding on its own, because it is the method every other method is checked against. A pipe leaking under pressure releases water through a break, and that water makes a sound: a hiss where it escapes the pipe, a rush where it moves through the soil. Concrete carries sound well, so the sound travels up through the slab and into the floor above — too quiet for the ear, but clear to a sensitive microphone placed on the floor.
The operator works across the floor with a ground microphone, listening at point after point and comparing the sound at each one. The sound grows louder as the sensor moves toward the leak and quieter as it moves away, and the loudest point marks the leak. The work is slow and methodical: a floor is listened to in a grid, the loudest points are checked again from another angle, and the location is confirmed before it is marked. A leak that is heard from several directions, with the sound converging on one spot, is a leak that is found.
The method has limits, and it is honest to name them. A slow leak makes less sound than a fast one. Thick stone flooring muffles the sound. A leak under a bathroom, with tile and fixtures, is harder to hear than a leak under a hallway. Background noise — a running appliance, a road outside, a neighbour's work — can mask the sound. That is why acoustic detection is rarely used alone: electronic line location traces the pipe, thermal imaging checks for heat, and tracer gas confirms the location when the sound is faint. The methods stack, and the location is marked only when they agree.
In McKinney, acoustic detection has a local reason to be thorough. The soil under the city is Houston Black clay, and a line that leaked once in clay soil can leak again a few feet away. The operator does not only listen for the loudest point; the line is mapped, and the sound is checked along its length. A second, quieter leak a few feet from the first is found the same way — by listening along the line, not just at the loudest spot.
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.
How acoustic leak detection works
The visit starts with the meter and pressure tests, because listening is only useful once a leak is confirmed. Every tap is turned off, the meter is watched, and the hot and cold lines are pressure-tested separately. A line that loses pressure is leaking, and the listening work starts on that line. A line that holds pressure is sound, and no amount of listening will find a leak in it.
Then the listening starts. The operator places a ground microphone on the floor and listens, moving across the room in a grid, comparing the sound at each point. The sound of a leak is a hiss or a rush, distinct from the hum of an appliance or the creak of a floor. The loudest point is marked, then checked again from another angle — the sound should converge on the same spot from every direction. Electronic line location confirms the pipe runs where the sound says it does.
When the methods agree, the leak is marked on the floor — a small area, usually no bigger than a dinner plate — and the report is written. The report records the line, the location, and the readings, and the repair plan is built from it. If the sound does not converge, or if the line location disagrees with the sound, the work continues with other methods — thermal imaging for a hot line, tracer gas for a quiet leak — until the location is confirmed.
What the service includes
Meter and pressure tests first
The leak is confirmed and the line is identified before any listening starts.
Grid listening
The floor is listened to point by point, comparing the sound at each one until the loudest spot is found.
Confirmation from another angle
The loudest point is checked again from a different direction, so the sound converges on one spot.
Line location check
Electronic location confirms the pipe runs where the sound says it does.
Leak marking and report
The leak is marked on the floor, and the report records the line, the location, and the readings.
How the work runs
Confirm the leak
Meter and pressure tests confirm a leak exists and identify the line.
Listen in a grid
The floor is listened to point by point, comparing the sound at each one.
Find the loudest point
The sound grows louder toward the leak; the loudest point marks it.
Confirm from another angle
The point is checked again from a different direction, and the line location is traced.
Mark and report
The leak is marked on the floor and the report is written.
Tools and methods used
Acoustic ground microphone
A sensitive microphone placed on the floor that hears the sound of escaping water through concrete.
Electronic pipe locator
Traces the buried line so the sound is read against the pipe path.
Pressure test gauge
Confirms the leak exists and identifies the line before listening starts.
When acoustic detection is not enough
A slow leak makes less sound than a fast one, and a leak under thick stone flooring is harder to hear than one under tile. Background noise can mask the sound, and a leak in a drain line makes no sound at all, because drain lines are not under pressure. In those cases the crew adds methods: tracer gas in the line, a thermal camera for hot lines, or a camera in the drain line. The methods stack until the location is confirmed, and the leak is not marked on the sound alone.
The other limit is the second leak. A home can have two leaks, and the louder one masks the quieter one. That is why the meter is checked again after every repair: a meter that still moves means there is more to find, and the listening starts again.
A leak under the slab, silent to the ear
A leak under the slab keeps running — washing out soil, lifting flooring, and stressing the foundation.
The leak heard, located, and marked
The leak is located with listening and electronic equipment before any concrete is opened.
Problems acoustic leak detection solves
- A leak that cannot be seen, only heard
- A damp patch with no visible source
- A bill that jumped, with no water in sight
- The sound of running water with every tap off
- A leak that needs locating before any floor is opened
Signs you need acoustic leak detection
- A water meter that moves with every tap off
- A damp patch on the floor with no visible source
- A bill that jumped without explanation
- The sound of running water when every tap is off
- A warm spot on the floor, on a hot line
- A previous repair, with the meter moving again
Related problems
Running water sound · Warm spot on the floor · Low water pressure
Industries that use this service
Commercial Offices · Retail Shops · Rental Properties · All industries →
Frequently asked questions
Questions people ask about acoustic leak detection, answered plainly.
A sensitive microphone is placed on the floor, and it hears the sound of water escaping a pipe through the concrete — a hiss or a rush that the ear cannot pick up. The operator moves across the floor, comparing the sound at each point, until the loudest spot marks the leak.
A slow leak makes less sound than a fast one, and it is harder to hear — especially through thick flooring. When listening alone is not enough, the crew adds methods: tracer gas in the line, or a thermal camera for a hot line. The methods stack until the location is confirmed.
No. It works from above the floor — a microphone placed on the surface, listening. The floor is opened only for the repair, and only over the marked leak area.
When the sound converges on one spot from several directions, and the electronic line location agrees, the leak is marked to a small area — usually no bigger than a dinner plate. The location is confirmed by more than one method before it is marked.
Some leaks are quiet — a slow drain-line leak, or a leak under thick stone flooring. The crew adds methods: tracer gas, thermal imaging, or a camera in the drain line. The leak is not marked on the sound alone.
The idea is the same — listening for the leak — but the equipment is different. A ground microphone is far more sensitive than the ear, and it is used with line location and pressure tests, so the location is confirmed by more than one method.
Slab leak in your McKinney home?
Call Now to reach a local slab leak professional. Describe the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped.
Call now for slab leak help
Tap Call Now to reach a local slab leak professional. Tell them the signs — a warm floor, damp flooring, the sound of running water, or a bill that jumped — and where in the house they show up.
Hours: Mon–Fri 7:00 AM–10:00 PM ET · Sat 8:00 AM–10:00 PM ET · Sun 7:00 AM–9:00 PM ET
Before you call
- Shut off the main water supply if it is safe to do so.
- Move valuables, rugs and electronics off wet floors.
- Take photos of the damp floor, the water meter, and the rooms affected.
- Stay away from wet outlets, switches and light fixtures.
- Note when the signs started, and whether the water meter moves when every tap is off.